一、產品簡介：
通信管內壁靜摩擦系數測試儀是檢測儀器，是測量通信管內壁靜摩察系數而設計和生產的，具有用性廣、測量精度高、測量安全及可靠性好等特點。符合中華人民共和國交通行業標準JT/T496-2004《公路地下通信管道高密度聚乙烯硅芯塑料管》相關技術標準的要求。
Product introduction:
Communication tube inner wall static friction coefficient tester is a testing instrument designed and produced for measuring the static wall observation coefficient of communication tube inner wall. It has the characteristics of wide utility, high measurement accuracy, good measurement safety and reliability. It meets the requirements of the relevant technical standards of the People's Republic of China Transportation Industry Standard JT / T496-2004 "High-density polyethylene silicon core plastic pipes for highway underground communication pipelines".
二、技術參數：
?測量范圍：0°～45°
?測量精度： 2.0′
?試棒重量：270±10g
?表層材料邵氏硬度：HD59±3
?表面粗糙度R a 值：0.20μm～0.50μm
?外形尺寸：600X750X1200mm
? 重量:150kg
Technical parameters:
? Measurement range: 0 ° ～ 45 °
? Measurement accuracy: 2.0 ′
? Test rod weight: 270 ± 10g
? Shore hardness of surface material: HD59 ± 3
? Surface roughness R a value: 0.20μm ～ 0.50μm
? Overall dimensions: 600X750X1200mm
? Weight: 150kg
三、操作步驟：
? 將試樣固定在V型鐵上，從右端插入試棒使一端露出20mm，拴好鏈繩。
? 輕微搖動手輪使V型鐵上水平泡處于水平位置。
? 打開角度尺緊固栓，轉動角度尺使角度尺與副尺歸零，擰緊緊固栓。
? 順時針搖動手輪，使V型鐵緩慢傾斜，直至試棒滑動為止。
? 記錄下角度尺示值。
? 逆時針搖動手輪，使V型鐵水平為止。
? 將試棒拉出通信管外露20mm。
? 按照以上操作步驟連續9次，計算出9次平均值。（傾斜角度≤14°4′依據JT/T683-2009《通信管道靜摩擦系數測量?jī)x》之規定要求）
Third, the operation steps:
? Fix the sample on the V-shaped iron, insert the test rod from the right end so that one end is exposed 20mm, and fasten the chain rope.
? Slightly shake the handwheel to make the horizontal bubble on the V-shaped iron in the horizontal position.
? Open the fastening pin of the angle ruler, turn the angle ruler to zero the angle ruler and the vice ruler, and tighten the fastening pin.
? Shake the handwheel clockwise to tilt the V-shaped iron slowly until the test rod slides.
? Record the displayed value of the angle ruler.
? Turn the handwheel counterclockwise until the V-shaped iron is level.
? Pull the test rod out of the communication tube to expose 20mm.
? Follow the above steps for 9 consecutive times and calculate the average of 9 times. (Tilt angle ≤14 ° 4 ′ according to the requirements of JT / T683-2009 "Communication Pipe Static Friction Coefficient Measuring Instrument")
四、結構組成：
主要由以下部分組成：
1、底座
2、手搖輪及傳動桿
3、蝸輪蝸桿
4、上底版
5、角度尺及副尺
6、V型卡鐵及水平裝置固定夾
7、試棒及鏈繩
Fourth, the structural composition:
It is mainly composed of the following parts:
1.Base
2.Handwheel and transmission rod
3, worm gear
4, on the bottom plate
5.Angle ruler and vice ruler
6, V-shaped iron and horizontal device fixing clip
7, test rods and chains
五、貯存條件：
測定器及其附件應存放在干燥、清潔、無振動、無易燃、易腐蝕物品的環境條件下。
6. Storage conditions:
The analyzer and its accessories should be stored in a dry, clean, vibration-free, flammable, and corrosive environment.
