一、設備用途：

該設備采用電子流量計、觸摸屏控制。主要用于木制品、家具、地板、地毯、鞋類產品、建筑裝修材料等消費品中游離態甲醛的測定。

I. Equipment use:

The device is controlled by electronic flow meter and touch screen. Mainly used for the determination of free formaldehyde in consumer products such as wood products, furniture, flooring, carpets, footwear products, construction and decoration materials.

二、產品概述：

將已知表面積的試件，放入溫度、濕度、空氣流速和空氣置換率控制在一定值的測試箱內。甲醛從試件中釋放出來，與箱內空氣混合，定期抽取箱內空氣，從箱中抽取空氣通過盛有水的洗氣瓶測定水中吸收的甲醛濃度。測試箱中空氣的甲醛濃度由洗氣瓶中的甲醛濃度和抽出的空氣體積計算，用毫克每立方米（mg/m3）表示。取樣是周期性的，直到測試箱內甲醛濃度達到平衡狀態。

Product Overview:

Put a test piece with a known surface area into a test box with controlled temperature, humidity, air velocity, and air replacement rate. The formaldehyde is released from the test sample, mixed with the air in the box, and the air in the box is periodically extracted. The air is extracted from the box and the concentration of formaldehyde absorbed in the water is measured through the air-wash bottle containing water. The formaldehyde concentration of the air in the test box is calculated from the formaldehyde concentration in the air wash bottle and the volume of the extracted air, and is expressed in milligrams per cubic meter (mg / m3). Sampling is periodic until the formaldehyde concentration in the test box reaches equilibrium.

三，環境倉設計參考標準：

《室內裝飾裝修材料 人造板及其制品中甲醛釋放》（GB 18580-2017）；

《甲醛釋放量檢測用1m 3 氣候箱》(LYT 1612-2004)

《小尺度環境箱測定木制品釋放氣體中甲醛濃度的標準測試方法》ASTM D 6007；

《人造板甲醛釋放量測量環境箱法》EN 717-1；

《人造板及飾面人造板理化性能測試方法》（GB/T17657-2013）；

《室內裝飾裝修材料木家具中有害物質》（GB18584-2001）；

《室內裝飾裝修材料地毯、地毯襯墊及地毯膠粘劑有害物質釋放》（GB18587—2001）；

《甲醛釋放量檢測用1M3氣候箱》（LY/T1980一2011）；

《1M3氣候箱法測定板材甲醛釋放量》（ISO 12460-1.2007）；

Third, the reference standard for environmental warehouse design:

"Interior decoration materials, formaldehyde release limit in wood-based panels and their products" (GB 18580-2017);

"1m 3 climatic chamber for detection of formaldehyde emission" (LYT 1612-2004)

"Standard Test Method for Determining the Formaldehyde Concentration in Gas Released from Wood Products by Small-scale Environmental Box" ASTM D 6007;

"Environmental Box Method for the Measurement of Formaldehyde Release from Wood-based Panels" EN 717-1;

"Test method for physical and chemical properties of wood-based panels and facing wood-based panels" (GB / T17657-2013);

"Limits of Harmful Substances in Wooden Furniture for Interior Decoration Materials" (GB18584-2001);

"Limits of harmful substances release for interior decoration materials carpets, carpet pads and carpet adhesives" (GB18587-2001)

"1M3 climatic box for the detection of formaldehyde emission" (LY / T1980-2011);

"Determination of Formaldehyde Release from Sheets by 1M3 Climate Box Method" (ISO 12460-1.2007);

四、性能特點：

●換熱器工藝**：換熱效率高，溫度梯度?。?/span>

●冷熱對抗調溫水箱：溫度控制穩定；

●進口濕度溫濕度傳感器：傳感器精度較高、性能穩定；

●優質制冷機：進口冷凍機，運行穩定、使用壽命長；

●保護裝置：氣候箱、露點水箱均有高低溫報警保護措施與高低水位報警；

●保護措施；壓縮機亦有過熱、過流、超壓保護措施，整機運行安全可靠；

●不銹鋼內箱體：恒溫箱體內腔采用鏡面不銹鋼，表面光滑不結露，不吸附甲醛，保證檢測精度；

●恒溫箱體保溫材料采用植物纖維不揮發甲醛。箱內裝有強制空氣循環裝置（形成循環空氣流），以確保箱內溫濕度均衡一致。

Performance characteristics:

● Heat exchanger technology **: High heat exchange efficiency and small temperature gradient;

● Cold and hot counter temperature tank: stable temperature control;

● Imported humidity temperature and humidity sensor: The sensor has high accuracy and stable performance;

● High-quality refrigerator: imported refrigerator, stable operation and long service life;

● Protection device: climate box and dew point water tank have high and low temperature alarm protection measures and high and low water level alarm;

● Protection measures; the compressor also has overheating, overcurrent, and overpressure protection measures, and the whole machine runs safely and reliably;

● Stainless steel inner box: The inner chamber of the constant temperature box is made of mirror stainless steel. The surface is smooth without dew condensation and does not adsorb formaldehyde to ensure detection accuracy.

● The constant temperature box insulation material uses plant fiber non-volatile formaldehyde. The box is equipped with a forced air circulation device (forming a circulating air flow) to ensure that the temperature and humidity in the box are balanced.

五、技術參數：

1.工作環境溫度：15℃～30℃ 工作環境濕度：≤90％RH

2.溫度可調范圍：10℃～40℃，控溫精度±0.1℃，波動率≤±0.5℃，均勻度≤±0.5℃

3.濕度可調范圍：30％～80％，控濕精度±2% RH ,波動率≤±3% RH，均勻度≤±5% RH

4.空氣交換率：1m3/h，±5% 壓力：10±5Pa

5.空氣流速：0.1m/s～0.3m/s(連續可調)，精度≤0.05m/s

6.氣密性：艙門具有自密性。密閉性能滿足：

① 在1kPa正壓（表壓）時，艙內空氣泄漏率少于10-3*1M3/min；

② 進出口氣體流量差小于1%。

7.內箱材質:304鏡面不銹鋼板無縫焊接，焊接處及周圍拋光、無變形，內壁平整光滑，色澤均勻，無露底、起層、鼓泡、劃痕。

8.外箱材質：A3彩鋼板靜電噴涂，涂鍍層平整光滑，色澤均勻，無露底、起層、鼓泡、斑痕、較深劃痕等缺陷，艙體及門有效熱絕緣，采用植物纖維保溫，保溫層厚度不小于50mm，導熱系數不大于0.01W/（m·K），內壁板之間的搭接處采用無縫焊接。

9.空氣交換裝置：艙體內部安裝能夠連續控制換氣率裝置（干空氣流量計，或其它電子空氣流動計量裝置）?？諝膺M口與出口應在不同的內壁上，并處于不同的高度，保障補充到艙內的空氣流量滿足相應標準要求。

10.空氣循環（混合）裝置：艙內安裝風扇，用于加強艙內空氣混合；試件表面附近的空氣流速在0.1m/s至0.3m/s之間（可調）

Five, technical parameters:

1. Working environment temperature: 15 ℃ ～ 30 ℃ Working environment humidity: ≤90% RH

2. Temperature adjustable range: 10 ℃ ～ 40 ℃, temperature control accuracy ± 0.1 ℃, fluctuation rate ≤ ± 0.5 ℃, uniformity ≤ ± 0.5 ℃

3. Adjustable range of humidity: 30% ～ 80%, humidity control accuracy ± 2% RH, fluctuation rate ≤ ± 3% RH, uniformity ≤ ± 5% RH

4. Air exchange rate: 1m3 / h, ± 5% Pressure: 10 ± 5Pa

5.Air velocity: 0.1m / s ～ 0.3m / s (continuously adjustable), accuracy≤0.05m / s

6. Air tightness: The door is self-tight. Sealing performance meets:

① At 1kPa positive pressure (gauge pressure), the air leakage rate in the cabin is less than 10-3 * 1M3 / min;

② The difference between inlet and outlet gas flow is less than 1%.

7.Inner box material: 304 mirror stainless steel plate is seamlessly welded, the welding place and its surroundings are polished, no deformation, the inner wall is smooth, the color is uniform, and there is no exposed bottom, layer formation, blisters, scratches.

8. Outer box material: A3 color steel plate is electrostatic sprayed, the coating is smooth and uniform, the color is uniform, and there are no defects such as exposed bottom, layer formation, blisters, scars, deep scratches, etc. The cabin and door are effectively thermally insulated, and plant fiber insulation , The thickness of the insulation layer is not less than 50mm, the thermal conductivity is not more than 0.01W / (m · K), and the overlap between the inner wall plates is seamlessly welded.

9. Air exchange device: A device (dry air flow meter, or other electronic air flow metering device) capable of continuously controlling the ventilation rate is installed inside the cabin. The air inlet and outlet should be on different inner walls and at different heights to ensure that the air flow replenished into the cabin meets the requirements of the corresponding standards.

10. Air circulation (mixing) device: a fan is installed in the cabin to enhance the air mixing in the cabin; the air velocity near the surface of the test piece is between 0.1m / s and 0.3m / s (adjustable)