防水卷材沖片機是檢測儀器，供防水材料橡膠廠及科研單位進行拉力試驗前沖切標準橡膠試片用。對于類似材料，本機亦可沖切。還可以供防水材料。橡膠廠裁取試件，本沖片機適用于沖裁位伸試片，及各種形狀的試件，廣泛用于建筑實驗室、科研單位及橡膠試樣取材。具有方便靈活、簡單易用等優(yōu)點。
The waterproof sheet punching machine is a testing instrument for punching standard rubber test pieces before the rubber material factory and research institutes conduct tensile tests. For similar materials, the machine can also die-cut. Also available for waterproof materials. The rubber factory cuts test pieces. This punching machine is suitable for punching test pieces and various shapes of test pieces. It is widely used in building laboratories, scientific research units and rubber samples. Has the advantages of convenient and flexible, simple and easy to use.
CP-25防水卷材沖片機使用方法：
沖片機根據(jù)不同試樣選擇相應的切刀，裝在該沖片機上壓板位置上。將料放在刀墊上，使絲杠下移，切刀與料相接觸。將控制旋鈕向壓樣方向旋轉，擰緊為止。用手上、下搬動操縱桿，使下壓板向上移動，壓樣完成后，將控制旋鈕向復位方向旋轉，下壓板自動復位。
How to use CP-25 waterproof sheet punching machine:
The punching machine selects the corresponding cutter according to different samples and installs it on the platen position on the punching machine. Put the material on the knife pad, move the screw down, and the cutter will contact the material. Turn the control knob towards the compression direction until it is tightened. Use your hands to move the joystick up and down to move the lower platen upward. After pressing the sample, turn the control knob to the reset direction, and the lower platen will automatically reset.
防水卷材沖片機技術規(guī)格：
★沖切行程：25mm
★工作臺尺寸：175×140(mm)
★外形尺寸：320mm×450mm×515mm
★重量：80kg
Waterproof sheet punching machine technical specifications:
★ Punching stroke: 25mm
★ Workbench size: 175 × 140 (mm)
★ Dimensions: 320mm × 450mm × 515mm
★ Weight: 80kg
CP-25防水卷材沖片機安裝：
★本機安裝時打好基礎，找好水平用m8膨脹螺栓固定即可。
★把裁刀輕輕放在絲杠下的沖壓柱底部，沖壓柱下面配有力磁鐵，能穩(wěn)固裁刀，安裝快捷，調整方便。
★試件沖壓時應在工作臺配備硬木或膠板以防損壞刀口。
★實驗完畢后應將表面清理干凈、絲杠、沖壓柱涂防銹油脂，套好防護罩。
CP-25 Waterproof Roll Punching Machine Installation:
★ When the machine is installed, lay the foundation, find the level and fix it with m8 expansion bolts.
★ Put the cutter lightly on the bottom of the stamping column under the screw. The super strong magnet is installed under the stamping column to stabilize the cutter, fast installation and easy adjustment.
★ When punching the test piece, the workbench should be equipped with hardwood or rubber board to prevent damage to the knife edge.
★ After the experiment is completed, the surface should be cleaned, the lead screw and stamped column should be coated with anti-rust grease, and the protective cover should be put on.
