漆膜劃格器根據ISO2409-1974標準設計制造的。主要適用于有機涂料附著力的測定。不僅適用于實驗室，也可用于各種條件下的施工現場。

The paint film divider is designed and manufactured according to ISO2409-1974 standard. Mainly applicable to the determination of adhesion of organic coatings. Not only suitable for laboratories, but also for construction sites under various conditions.

漆膜劃格器工作原理和適用范圍:

該儀器以一定規格的工具將涂層做格陣圖形切割并穿透，規格完成的圖形按六級分類，評定涂層從底材分離的抗性。

本劃格器有三種規格間距的多刃切割刀（1mm、2mm、3mm）按不同實驗條件可供選擇。1mm間距的多刃切割刀適用于涂膜厚度<60um的試片，2mm間距的多刃切割刀適用于涂膜厚度<60~120um的試片，3mm間距的多刃切割刀是為特殊用途而設計的。

The working principle and scope of the paint film divider:

The instrument uses a certain specification tool to cut and penetrate the coating into a lattice pattern. The completed graphics are classified into six grades to evaluate the resistance of the coating to separation from the substrate.

This grid divider has three specifications of multi-blade cutting blades (1mm, 2mm, 3mm) to choose from according to different experimental conditions. Multi-blade cutting blade with 1mm pitch is suitable for test pieces with coating film thickness <60um, multi-blade cutting blade with 2mm pitch is suitable for test pieces with coating film thickness <60 ~ 120um. Designed.

漆膜劃格器特點：

用于均勻劃出一定規格尺寸的方格，通過評定方格內涂膜的完整程度來評定涂膜對基材附著程度，以‘級’表示。它主要用于有機涂料劃格法附著力的測定，不僅適用于實驗室，也可用于各種條件下的施工現場。（這種刀片及加工工藝，只適用于非金屬和軟金屬基材上面的涂層的附著力測試，需要均衡用力使每條劃痕都劃穿涂層）。

Features of the paint film divider:

It is used to uniformly draw a grid of a certain size. The degree of adhesion of the coating film to the substrate is evaluated by evaluating the completeness of the coating film in the grid, which is expressed as 'grade'. It is mainly used for the determination of the adhesion of organic paint by the grid method. It is not only suitable for laboratories but also for construction sites under various conditions. (This kind of blade and processing technology is only suitable for the adhesion test of coatings on non-metal and soft metal substrates, and it needs to be balanced to force each scratch to penetrate the coating).

漆膜劃格器技術參數：

★ 多刃切割刀間距分別為：

1±0.01mm

2±0.01mm

3±0.01mm

★多刃切割刀齒頂直線分別為：

不小于0.003mm(1±0.01mm)

不小于0.006mm（2±0.01mm,3±0.01mm）

★多刃割刀工作齒寬度：不小于0.05mm

Technical parameters of paint film divider:

★ Multi-blade cutting knife spacing is:

1 ± 0.01mm

2 ± 0.01mm

3 ± 0.01mm

★ The straight lines of the multi-blade cutting blades are:

Not less than 0.003mm (1 ± 0.01mm)

Not less than 0.006mm (2 ± 0.01mm, 3 ± 0.01mm)

★ Multi-blade cutter working tooth width: not less than 0.05mm

漆膜劃格器使用方法：

★試片必須按ISOR1514及ISO2808的規定制備：

★將試片放置在有足夠硬度的平板上：

★根據需要實驗的涂膜厚度，選用規格合適的多刃切割刀，將圖中件2

松開一圈，搬動刀體3或螺紋軸1，即可改換多刃切割刀，然后鎖緊件2即能使用：

★手持劃格器手柄，使多刃切割刀垂直于試片平面：

★以均勻的壓力，平穩地不顫動的手法和20~~50mm/s的切割速度割劃；

★將試片旋轉90度角，在所割劃的切口上重復以上操作，以使形成格陣圖形；

★用軟毛刷沿格陣圖形的，兩對角線輕輕地向后5次向前5次的刷試片；

★試驗至少在試片的三個不同位置上完成，如果三個位置的實驗結果不同，應在多于三個位置上重復試驗，同時記錄全部結果。

How to use the paint film divider:

★ Test strips must be prepared in accordance with ISOR1514 and ISO2808:

★ Place the test piece on a plate with sufficient hardness:

★ According to the required coating film thickness, choose a multi-blade cutting knife with appropriate specifications, and change the part 2 in the figure.

Loosen it once, move the knife body 3 or the threaded shaft 1, you can change the multi-blade cutting knife, and then the locking piece 2 can be used:

★ Hold the handle of the grid divider so that the multi-blade cutting knife is perpendicular to the plane of the test piece:

★ Slitting with uniform pressure, smooth and non-vibrating technique and cutting speed of 20 ~ 50mm / s;

★ Rotate the test piece by 90 degrees, and repeat the above operation on the cut incision to form a lattice pattern;

★ Use a soft-bristled brush to brush the test strip along the grid pattern, gently diagonally back 5 times forward 5 times;

★ The test is completed at least in three different positions on the test strip. If the test results in the three positions are different, the test should be repeated in more than three positions and all results should be recorded at the same time.

QFH漆膜劃格器工作面數：
★六面：1mm 25格、1mm 100格、1.5mm 100格、2mm 25格（塑料手柄）
★四面：2mm 100格、3mm 25格（木手柄）
★單面：1mm 100格、2mm 100格（木手柄）另配備用刀片1片

Number of working faces of QFH paint film grid:

Six sides: 1mm 25 grid, 1mm 100 grid, 1.5mm 100 grid, 2mm 25 grid (plastic handle)

★ 4 sides: 2mm 100 grid, 3mm 25 grid (wood handle)

★ Single side: 1mm 100 grids, 2mm 100 grids (wood handle), 1 blade

QFH漆膜劃格器注意事項：

★所有切口應穿透涂層，但切入底材不得太深；

★如因涂層過厚和過硬而不能穿透到底材，則該試驗無效，應在試驗報告中說明；

★在特殊情況下或有特殊要求時必須配合膠帶測定。膠帶一般是25 mm寬的半透明膠帶，背材為聚脂薄膜或醋酸纖維。將膠帶貼在整個劃格器上，然后以A小角度撕下，結果可用漆膜表面與脫落面積的比例來求得：

★實驗應在溫度23±2°C和相對濕度50±5%中進行

Note for QFH paint film divider:

★ All cuts should penetrate the coating, but the cut into the substrate should not be too deep;

★ If the coating is too thick and too hard to penetrate the substrate, the test is invalid and should be stated in the test report;

★ Under special circumstances or special requirements, it must be measured with tape. The tape is generally a 25 mm wide translucent tape with a polyester film or acetate backing. Stick the adhesive tape on the entire scale, and then tear it off at a small angle.

★ The experiment should be performed at a temperature of 23 ± 2 ° C and a relative humidity of 50 ± 5%