QCJ-120漆膜沖擊器用于以固定質量的重錘落于試板上而不引起漆膜破壞的A大高度120厘米表示的漆膜耐沖擊性試驗。符合GB/T1732—93漆膜耐沖擊測定法標準。

QCJ-120 paint film impactor is used to test the impact resistance of paint film with a large height of 120 cm when the weight of fixed mass is dropped on the test panel without causing paint film damage. Meet GB / T1732-93 paint film impact resistance test method standard.

QCJ-120漆膜沖擊器技術指標：

★儀器刻度長:120±0.2cm

★分度 : 1cm

★錘體質量:1000±1g

★沖頭規格: S￠8mm

★枕墊塊凹孔直徑:￠15mm

★曲率半徑: R2.5-3mm

★沖擊頭沖頭深度: 2±0.1mm

★型 號:QCJ -120A

★儀器刻度長: 120±0.2cm

★分度:1cm

★錘體質量:1000±1g

★沖頭規格: S￠16mm

★枕墊塊凹孔直徑:￠15mm

★曲率半徑R2.5-3mm

★沖擊頭沖頭深度: 2.5±0.1mm

★型 號:QCJ-120B

★儀器刻度長度120±0.2cm

★分度:1cm

★錘體質量2000±2)g

★沖擊頭規格S直徑16mm

★枕墊塊凹孔直徑16.3mm

★曲率半徑R2.5-3mm

★沖擊頭沖擊深度（2.5±0.1）mm

Technical index of QCJ-120 paint film impactor

★ Instrument scale length: 120 ± 0.2cm

Indexing: 1cm

Mass of hammer body: 1000 ± 1g

★ Punch specifications: S ￠ 8mm

Pillow block recess diameter: 枕 15mm

★ Curvature radius: R2.5-3mm

★ Depth of impact head: 2 ± 0.1mm

Type: QCJ -120A

★ Instrument scale length: 120 ± 0.2cm

Indexing: 1cm

Mass of hammer body: 1000 ± 1g

★ Punch specifications: S ￠ 16mm

Pillow block recess diameter: 枕 15mm

★ Curvature radius R2.5-3mm

★ Depth of impact head: 2.5 ± 0.1mm

Type: QCJ-120B

★ Instrument scale length 120 ± 0.2cm

Indexing: 1cm

★ Mass weight 2000 ± 2) g

★ The impact head size S diameter 16mm

★ Diameter of recessed hole of pillow block 16.3mm

★ Curvature radius R2.5-3mm

★ Impact depth of impact head （2.5 ± 0.1） mm

QCJ-120漆膜沖擊器工作原理：

由控制器螺釘將帶有掛鉤的重錘固定在所要求的高度上，其高度即滑筒刻度所示高度刻線與定位標刻線重合。按壓控制螺釘則控制器彈簧被壓縮，此時控制滑塊的圓孔與控制器上蓋及控制器下底的圓孔對正使掛鉤脫落，重錘落下，撞擊沖桿，沖桿向下作用在事先放在枕墊塊上的試板上。之后，提升重錘體，取出試板，以觀察試板上漆膜試驗情況。

QCJ-120 paint film impactor working principle

The weight of the hammer with the hook is fixed to the required height by the controller screw, and its height, that is, the height engraved line indicated by the cylinder scale coincides with the positioning engraved line. When the control screw is pressed, the controller spring is compressed. At this time, the round hole of the control slider is aligned with the round hole of the upper cover of the controller and the bottom of the controller to make the hook fall off. On a test panel that has been placed on a pillow block in advance. After that, lift the weight body and take out the test plate to observe the paint film test on the test plate.

QCJ-120漆膜沖擊器操作與使用：

準備，使用前，請?jiān)敿?xì)閱讀本說明書。

調零。檢查定位標是否對零線，如有偏差，將重錘降落到滑筒底部（因沖桿部分裝有復位彈簧，重錘需沿滑道向下按壓，才能降到底部）。調節定位標兩側螺釘。使定位標上刻線與零線重合。

底座留有二個安裝孔，可用M12螺栓將沖擊器穩裝在平坦的地面或工作臺上。

QCJ-120 paint film impactor operation and use

Read and read this manual before use.

Zero. Check whether the positioning mark is aligned with the zero line. If there is a deviation, lower the weight to the bottom of the slide tube (because the reset spring is installed in the punch rod, the weight must be pressed down the slide rail to lower to the bottom). Adjust the screws on both sides of the positioning mark. Make the mark on the positioning mark coincide with the zero line.

The base has two mounting holes, and the impactor can be stably mounted on a flat floor or a worktable with M12 bolts.

QCJ-120漆膜沖擊器操作：

試板的放置。把備妥的試板放置在枕墊塊上，且緊貼于枕墊塊凹孔，漆膜朝上，使受沖擊點距試板邊緣不少于15mm，或在試板中間處。若使用一個試板作數次試驗時，應使每個沖擊點邊緣相距不少于15mm。

重錘投放高度的設置。同時松動控制器螺釘，控制器件可按滑筒兩側滑道上下移動。根據試驗要求，先取高度時，請將定位標上刻線與滑筒刻度線重合即可，將控制器螺釘擰緊、固定。

試驗舉例。依照標準中的有關規定，完成重錘投放高度的設置，將制備好的試板置于枕墊塊上。按壓控制螺釘，重錘即自由地落在沖桿上，沖桿將沖擊力傳給枕墊塊上的試板。將重錘提升起，由控制器掛住重錘上的掛鉤，取出試板。用4倍放大鏡觀察，判斷漆膜有無裂紋、皺紋及剝落等現象。本試驗舉例僅供參考，具體的試驗方法，以標準中的有關規定為準。

QCJ-120 paint film impactor operation

Placement of test plates. Place the prepared test plate on the pillow block and close to the recessed hole of the pillow block with the paint film facing up so that the impact point is not less than 15mm from the edge of the test plate, or in the middle of the test plate. If a test plate is used for several tests, the distance between the edges of each impact point shall be not less than 15mm.

Setting of the weight drop height. At the same time loosen the controller screw, the control device can move up and down according to the slide rails on both sides of the slide. According to the test requirements, when taking the height first, you can overlap the engraved line on the positioning mark with the scale line of the sliding cylinder, and then tighten and fix the controller screws.

Test example. According to the relevant provisions in the standard, complete the setting of the height of the weight hammer, and place the prepared test plate on the pillow block. When the control screw is pressed, the weight is freely dropped on the punch, and the punch transmits the impact force to the test plate on the pillow block. Raise the weight, hold the hook on the weight by the controller, and remove the test plate. Observe with a 4x magnifying glass to determine whether the paint film has cracks, wrinkles and peeling. This test example is for reference only. The specific test method is subject to the relevant provisions in the standard.

QCJ-120漆膜沖擊器維護與保養：

儀器應置于干燥、清潔、無腐蝕性氣體環境中。儀器應經常保持清潔，運動部分靈活。

當控制器因保管或使用不當有障礙時，可用內六角扳手松開支臂上M10內六角螺釘，將滑筒卸下，然后擰下控制器螺釘，重錘及兩側螺釘，由管底部用改錐卸下定位標支架緊固螺釘，即可將控制器取出進行清潔、修理。

QCJ-120 Paint Film Impactor Maintenance

The instrument should be placed in a dry, clean, non-corrosive gas environment. The instrument should always be kept clean and the moving parts flexible.

When the controller has obstacles due to improper storage or use, you can use an Allen wrench to loosen the M10 Allen screws on the arm, remove the slide tube, and then remove the controller screws, weights and screws on both sides. Use a screwdriver at the bottom of the tube Remove the positioning bracket fixing screws to take out the controller for cleaning and repair.