洛杉磯磨耗儀是**檢測儀器，主要適用測定石料的磨耗率。

The Los Angeles Abrasion Tester is a testing instrument that is mainly used to determine the abrasion rate of stone.

洛杉磯磨耗儀技術參數：

★圓筒內經×內長：710mm×510mm(±5mm)

★轉速：30-33轉/分

★計數器：4位

★外形尺寸：1100×780×100(長X寬X高)

★鋼球：φ50（1個）φ47.5(7個)φ44.5(3個) φ42.8(1個)總重量5000g±50g

Los Angeles abrasion meter technical parameters:

★ Inner Warp × Inner Length: 710mm × 510mm (± 5mm)

★ Speed: 30-33 rpm

★ Counter: 4 digits

★ Dimensions: 1100 × 780 × 100 (length x width x height)

★ Steel balls: φ50 (1) φ47.5 (7) φ44.5 (3) φ42.8 (1) Total weight 5000g ± 50g

洛杉磯磨耗儀調試與安裝：

★啟動前**先檢查旋轉部分與料筒是否有刮碰現象，應及時調整。

★減速箱應注入機油后方能使用，卸料蝸輪會及滑動軸承處注入機油。

★清理料筒內染料。洛杉磯擱板式磨耗試驗機

★啟動前將筒體限裝置鎖緊，然后再啟動。

★啟開后發現運轉方向不符合要求時，應切斷電源，將導線的任意兩根相線互換位置，再重新啟動。

★根據磨耗時間調整時間繼電器的定時，注意在斷電情況下調整。

★按動啟動按鈕。

★達到調定時間后自動停車。

★卸料時先停機，然后將筒體位限置手柄松開，再旋轉手輪，由蝸輪付帶料筒旋轉到便于出料的位置，停止轉動，然后啟動機器使主軸運轉方可排出物料，直至將料排出停止，主軸運轉旋轉手輪使料筒復位。洛杉磯擱板式磨耗試驗機

★清洗料筒，將水倒入料筒內使主軸運轉將料筒和鏟片沖洗干凈或用砂子清洗也可。

Los Angeles Abrasion Meter Commissioning and Installation:

★ Before starting ** Check if there is any scratch between the rotating part and the barrel, it should be adjusted in time.

★ The reduction gear box can be used only after being filled with engine oil. The discharge worm gear and the sliding bearing will be filled with engine oil.

★ Clean the dye in the barrel. Los Angeles Shelf Wear Tester

★ Lock the cylinder limit device before starting, and then start again.

★ When the running direction is found not to meet the requirements after starting, the power should be cut off, any two phase wires of the conductors should be swapped, and then restarted.

★ Adjust the timing of the time relay according to the wear time, and pay attention to the adjustment in the case of power failure.

★ Press the start button.

★ Automatically stop after reaching the set time.

★ Stop the machine when unloading, then release the cylinder position limiting handle, and then rotate the handwheel to rotate the worm gear with the material barrel to a position convenient for discharging. Until the discharge of the material stops, the spindle rotates to turn the handwheel to reset the barrel. Los Angeles Shelf Wear Tester

★ Clean the barrel, pour water into the barrel and run the spindle to rinse the barrel and blade or clean with sand.

洛杉磯磨耗儀使用方法：

★試車前必須檢查線路是否完好，（輸入電源必須為三火）按點動鍵，滾筒旋轉是否正常（按筒上箭頭方向，如果轉動方向相反，把輸入380V中兩相火線調換即改變）同時將LED顯示屏清零再把予置撥碼開關調到所試驗次數，按啟動鍵開始工作，如有特殊情況請按“暫停"鍵,機器停止工作,待故障排除后再次按“啟動"鍵機器恢復工作.

★將試驗的碎石料和鋼球裝入筒內，密封蓋好，擰緊螺釘，開動儀器轉動500轉或1000轉后自動停止。此時出料口在中上位置，便于打開密封蓋，打開蓋后，按點動鍵，使出料口轉向下方，松開按鍵試筒停止，取出試件。

★用直徑2mm圓孔篩或邊長1.7mm方孔篩，篩去試樣中的石屑，用水沖洗留在篩上的碎石，烘干、恒重，準確稱出重量。

How to use Los Angeles Abrasion Meter:

★ Before the test run, you must check whether the line is intact. (The input power must be three fires.) Press the jog key to check whether the drum rotates normally. Reset the LED display to zero and then set the pre-dial switch to the number of tests. Press the start key to start work. If there are special circumstances, press the "pause" key. The machine stops working. After the fault is removed, press the "start" key again. The machine resumes work.

★ Put the crushed stone and steel ball into the cylinder, seal it tightly, tighten the screws, and stop automatically after turning the instrument to rotate 500 or 1000 times. At this time, the discharge opening is in the middle and upper position, which is convenient for opening the sealing cover. After opening the cover, press the jog key to turn the discharge opening downward. Release the button to stop the test cylinder and remove the test piece.

★ Use a circular hole sieve with a diameter of 2mm or a square hole sieve with a side length of 1.7mm to remove the stone debris from the sample, rinse the crushed stone left on the sieve with water, dry and constant weight, and accurately weigh it.

洛杉磯磨耗儀計算方法：

★按下列計算石料磨耗率**至0.1% Q磨=(G1-G2)/G1×% 式中：Q磨--石料的磨耗率% G1--裝入筒中碎石之原重量g G2--試驗后，洗凈烘干之重量g

★試驗結果兩次試驗之平均值，兩次誤差不大于2%否則重新試驗。

Loss abrasion meter calculation method:

★ Calculate the stone wear rate ** to 0.1% according to the following Q grinding = (G1-G2) / G1 ×% where: Q grinding--the stone grinding wear rate% G1--the original weight of the crushed stone in the tube g -Weight after washing and drying g

★ Test results The average of two tests, the error between the two tests is not greater than 2%, or the test is repeated.

洛杉磯磨耗儀操作規程：

★啟動前**先檢查旋轉部分與料筒是否有刮碰現象，應及時調整。

★減速箱應注入機油后方能使用，卸料蝸輪會及滑動軸承處注入機油。

★清理料筒內染料。

★啟動前將筒體限裝置鎖緊，然后再啟動。

★啟開后發現運轉方向不符合要求時，應切斷電源，將導線的任意兩根相線互換位置，再重新啟動。

★根據磨耗時間調整時間繼電器的定時，注意在斷電情況下調整。

★按動啟動按鈕。

★達到調定時間后自動停車。

★卸料時先停機，然后將筒體位限置手柄松開，再旋轉手輪，由蝸輪付帶料筒旋轉到便于出料的位置，停止轉動，然后啟動機器使主軸運轉方可排出物料，直至將料排出停止，主軸運轉旋轉手輪使料筒復位。

★清洗料筒，將水倒入料筒內使主軸運轉將料筒和鏟片沖洗干凈或用砂子清洗也可。

Los Angeles abrasion meter operating procedures:

★ Before starting ** Check if there is any scratch between the rotating part and the barrel, it should be adjusted in time.

★ The reduction gear box can be used only after it is filled with oil. The discharge worm gear and the sliding bearing will be filled with oil.

★ Clean the dye in the barrel.

★ Lock the cylinder limit device before starting, and then start again.

★ When the running direction is found not to meet the requirements after starting, the power should be cut off, any two phase wires of the conductors should be swapped, and then restarted.

★ Adjust the timing of the time relay according to the wear time, and pay attention to the adjustment in the case of power failure.

★ Press the start button.

★ Automatically stop after reaching the set time.

★ Stop the machine when unloading, then release the cylinder position limiting handle, and then rotate the handwheel to rotate the worm gear to the material feeding barrel to a position convenient for discharging. Until the discharge of the material stops, the spindle rotates to turn the handwheel to reset the barrel.

★ Clean the barrel, pour water into the barrel and run the spindle to rinse the barrel and blade or clean with sand.

洛杉磯磨耗儀注意事項：

★設備不宜在磁場或電場中操作使用，必須采取屏蔽措施，防止儀器設備損壞或降低測量精度。

★使用前必須進行空載運轉確保后方可加載使用。用前潤滑，用后擦試干凈。

★不準隨意拆改或解體使用，確因需要開發新功能或改造更新等，需按分級管理權限，履行審批手續后再實施。

★經常進行 設備的保養與維護，并存放在干燥通風之處，待用時間過長儀器設備，應定期通電開機，防止潮霉損壞儀器設備其零部件

Note for Los Angeles Abrasion Tester:

★ The equipment is not suitable for operation and use in magnetic or electric fields. Shielding measures must be taken to prevent damage to the equipment or reduce the measurement accuracy.

★ No-load operation must be performed before use to ensure no trouble before loading and using. Lubricate before use and wipe clean after use.

★ It is not allowed to dismantle, dismantle, or disassemble at will. Due to the need to develop new functions or renewal, etc., it is necessary to manage permissions according to the hierarchy and implement the approval procedures.

★ Frequently perform equipment maintenance and storage, and store it in a dry and ventilated place. The instrument and equipment should be turned on and turned on regularly to prevent moisture and mildew from damaging its parts and components.