砌墻磚收縮膨脹儀是測量長度變化的精密儀器，它適用于砌墻磚生產廠、科研單位、大專院校、建工部門等單位用來檢測燒結普通磚、粉煤灰磚等砌墻磚的收縮及膨脹變形量。該產品是依據GB/T2542-2003《砌墻磚實驗方法》標準制作的。

由：底座、試樣架、測量表架、上測頭、緊固螺釘、下測頭、百分表、標準桿、試體固定螺釘、底座調整螺絲等組成。該產品是依據GB/T2542-2012《砌墻磚試驗方法》標準設計制作，上下測頭采用90°錐形凹座。具有使用方便、測量精度高、速度快、讀數清楚等特點。

The wall brick shrinkage dilatometer is a precision instrument for measuring the change of length. It is suitable for wall brick manufacturers, scientific research units, universities, construction departments and other units to detect sintered ordinary bricks, fly ash bricks and other wall bricks The amount of contraction and expansion deformation. This product is made according to the standard of GB/T2542-2003 "Experimental Method of Wall Bricks".

Consists of: base, sample holder, measuring table holder, upper probe, fastening screw, lower probe, dial indicator, standard rod, specimen fixing screw, base adjustment screw, etc. This product is designed and manufactured in accordance with the standard of GB/T2542-2012 "Test Method for Wall Bricks", and the upper and lower probes use 90° conical recesses. It has the characteristics of easy use, high measurement accuracy, fast speed and clear readings.

砌墻磚收縮膨脹儀技術參數：

1、測量范圍：251mm～261mm

2、標準桿長度：（256±0.02）mm；

標準桿測頭球面半徑：SR=2.25mm；

3、百分表量程：0-10mm

最小刻度值: 0.01mm；

4、外形尺寸（長×寬×高）：670×240×180mm

5、質量：≈10kg

Technical parameters of masonry brick shrinkage dilatometer:

1. Measuring range: 251mm～261mm

2. Standard rod length: (256±0.02) mm;

Standard rod probe spherical radius: SR=2.25mm;

3. Dial indicator range: 0-10mm

Minimum scale value: 0.01mm;

4. Dimensions (length×width×height): 670×240×180mm

5. Mass: ≈10kg

砌墻磚收縮膨脹儀注意事項：

1、使用時，忌用手直接與標準棒接觸，應持外外套部分，以防止標準棒受人體手溫的影響。

2、儀器用完畢后，應將測量框架的測量頭和百分表探拭凈，并涂以鐘表油；測試過程中，應使百分表的測頭緩慢而平穩地與試件接觸，不允許沖擊和碰撞，嚴禁將百分表測桿頂過量程范圍，以免影響表的靈敏度和使用壽命。

砌墻磚收縮膨脹儀試驗方法：

1、先將標準棒置于工作臺上，擰動調整螺絲使之近似垂直。

2、將測量框架置于標準棒的頂頭，調整螺桿和螺母，使百分表對準零位（或記下百分表之刻度）。

3、將制作養護好的試件兩端擦拭凈，然后放置在工作臺上，然后把測量框架套在試件上，并左右移動表框，使試件與測量框架的測量頭準確地接觸，此時即可開始讀數，并記錄下表盤上的刻度值。

4、如果實驗不是連續進行或?qū)嶒?yàn)歷時較

Precautions for wall brick shrinkage dilatometer:

1. When in use, avoid direct contact with the standard rod with your hands, and hold the outer cover part to prevent the standard rod from being affected by the temperature of the human hand.

2. After the instrument is used, the measuring head of the measuring frame and the dial indicator should be probed and wiped clean and coated with watch oil; during the test, the probe of the dial indicator should be brought into contact with the test piece slowly and steadily. Shocks and collisions are allowed, and it is strictly forbidden to push the dial indicator rod beyond the maximum range, so as not to affect the sensitivity and service life of the meter.

Test method of wall brick shrinkage dilatometer:

1. Put the standard bar on the workbench first, and turn the adjusting screw to make it approximately vertical.

2. Place the measuring frame on the top of the standard rod, adjust the screw and nut to make the dial indicator align to the zero position (or record the scale of the dial indicator).

3. Wipe the two ends of the cured test piece clean, and then place it on the workbench, then put the measuring frame on the test piece, and move the table frame left and right to make the test piece accurately contact the measuring head of the measuring frame. Reading can be started at this time, and record the scale value on the dial.

4. If the experiment is not continuous or the experiment lasts longer