一，產品簡介：
建筑石膏稠度儀是石膏檢測儀器，用于測定建筑石膏的標準稠度設備，因此它適用于制作建筑石膏制品的生產單位和有關科研部門。產品符合GB9776標準要求。
Product introduction:
The building gypsum consistency meter is a gypsum detection instrument, which is used to determine the standard consistency of building gypsum. Therefore, it is suitable for production units and related scientific research departments that make building gypsum products. The product meets the requirements of GB9776 standard.
二，技術參數：
?稠度筒提升速度：150mm/s。
?包裝尺寸：48×37×67cm。
?毛重/凈重：30/22kg。
?電壓功率：380V/60w。
Technical parameters:
? Consistency cylinder lifting speed: 150mm / s.
? Packing size: 48 × 37 × 67cm.
? Gross weight / net weight: 30 / 22kg.
? Voltage power: 380V / 60w.
三，使用方法：
?操作前先將電源接通（紅色信號燈兩），并把上升下降開關，調整在上升位置，接著用潔凈的濕毛巾將稠度筒內部及玻璃板擦凈并保持濕潤，把玻璃板歸整的放在工作臺面上。
?通過起落架的圓孔將稠度筒置于玻璃板的正中（即放在同心圓的正中）。
?待石膏稠度試驗程序告一段落后按啟動按鈕于是稠度筒在起落架上以150mm/s的速度垂直上升至上限位停止機械運動為止，取出稠度筒。
?復位時，把上升下降開關調到下降位置，按啟動按鈕，起落架復位。如復位有誤差可借助絲桿的上軸端的矩形槽使絲桿轉動從而使起落架復位。
?注意：當用戶電源相位與調試時相反時，則回出現絲桿反轉，從而出現相反方向的運動。此時，用戶可將插座任兩相互換，則能正常。
Second, use method:
? Turn on the power (two red signal lights) before operation, and adjust the ascending and descending switches to the ascending position. Then wipe the inside of the consistency tube and the glass plate with a clean wet towel and keep it moist. On the work surface.
? Place the consistency tube in the middle of the glass plate (that is, in the middle of the concentric circle) through the round hole of the landing gear.
? After the plaster consistency test procedure is completed, press the start button, so the consistency cylinder rises vertically on the landing gear at a speed of 150mm / s to the upper limit to stop the mechanical movement, and then remove the consistency cylinder.
? When resetting, turn the up and down switch to the down position and press the start button to reset the landing gear. If there is an error in the reset, the screw can be rotated by the rectangular groove on the upper shaft end of the screw to reset the landing gear.
? Note: When the phase of the user's power supply is opposite to that during debugging, the screw reversal will occur, resulting in movement in the opposite direction. At this time, the user can change any two sockets, and it is normal.
四、安放：
利用底座下四個調平螺栓，用麻繩起吊安放。
本儀器應安放在無震源及周圍無腐蝕介質的環境中。
本儀器應安放在適當高度的平臺上，并在安放時注意水泡對中。
維護保養：
用后清理，抹干凈。用罩子罩好。
Fourth, placement:
Use the four leveling bolts under the base to lift and place with hemp rope.
The instrument should be placed in an environment free of vibration sources and surrounding non-corrosive media.
The instrument should be placed on a platform of appropriate height, and the blister should be centered when placed.
maintenance:
Clean and wipe clean after use. Cover it with a hood.
